Grundfos Pumpen

Selbstansaugende Pumpe mit 24-Liter-Drucktank • Saughöhe bis zu 8 Meter.• Material: Edelstahl (AISI 304) und Verbundwerkstoff.• Automatischer Start/Stopp (gesteuert durch Druckschalter und Tank).

Selbstansaugende Pumpe • Saughöhe bis zu 8 Meter. • Material: Edelstahl (AISI 304) und Verbundwerkstoff.

Unilift KP 150 AV 1 Tauchpumpe Vertikale einstufige Edelstahl-Tauchpumpe mit vertikalem Auslass und integriertem einphasigen Tauchmotor der Isolationsklasse F mit thermischem Überlastschutz. Die Pumpe ist mit einem Saugkorb und einem Tragegriff ausgestattet und wird mit einem 10 mm Netzkabel sowie einem vertikalen Niveauschalter für automatischen Start und Stopp geliefert. Der Laufrad ist ein halboffenes Laufrad für einen freien Durchgang von 10 mm, geeignet zum Pumpen von Grundwasser, Oberflächenwasser, Regenwasser und ähnlichen Flüssigkeiten. Die Pumpe hat eine doppelte Wellendichtung bestehend aus zwei Lippenabdichtungen mit Fett dazwischen. Die Pumpe hat ein Außengehäuse, das durch die gepumpten Flüssigkeit eine kontinuierliche Kühlung des Motors gewährleistet. Der Rotorwellenbetrieb erfolgt in zwei wartungsfreien Kohlenstofflagern, die durch die gepumpten Flüssigkeit gekühlt werden.Der Motor ist gefüllt mit einer ungiftigen Motorflüssigkeit.Flüssigkeit:Flüssigkeitstemperaturbereich:0 .. 50 °CTechnisch:Höchstpartikelgröße:10 mmMaterial:Pumpengehäuse:EdelstahlPumpengehäuse:DIN W.-Nr. 1.4301Pumpengehäuse:AISI 304Laufrad:EdelstahlLaufrad:DIN W.-Nr. 1.4031Laufrad:AISI 304Installation:Pumpenauslass:Rp 1 1/4Maximale Installationshöhe:10 mElektrische Daten:Eingangsleistung - P1:300 WNennspannung:1 x 220-230 VNennstrom:1,3 AKondensatorgröße - Lauf:8 F/400 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC 85):FLänge des Kabels:10 mTyp des Kabelsteckers : SchukoAndere:Nettogewicht :6,5 kgBruttogewicht :7 kgVersandvolumen :0,013 m3

The Grundfos Unilift KP 150 A 1 basement and bilge pump is a vertical single-stage submersible pump made of stainless steel with a vertical outlet. The pump has an inlet strainer and lifting bracket and is supplied with a 10 m mains cable and float switch for automatic start/stop. The impeller is a semi-open impeller with a free passage of 10 mm suitable for pumping groundwater, surface water, rainwater and similar media. The pump has a double shaft seal consisting of two lip seals with grease in between. The outer casing of the pump ensures constant cooling of the motor by means of the pumped medium. The rotor shaft runs in two maintenance-free carbon bearings, which are cooled by the pumped medium. The motor is filled with a non-toxic liquid. 

Unilift KP 250 AV 1Tauchpumpe für die EntwässerungVertikale einstufige Tauchpumpe aus Edelstahl mit vertikalem Auslass und integriertem einphasigen Tauchmotor in Isolationsklasse F mit thermischem Überlastschutz. Die Pumpe ist mit einem Saugkorb und einem Tragegriff ausgestattet und wird mit einem 10 mm Netzkabel sowie einem vertikalen Niveauschalter für automatischen Start und Stopp geliefert.Das Laufrad ist ein halboffenes Laufrad für einen freien Durchgang von 10 mm, geeignet zum Pumpen von Grundwasser, Oberflächenwasser, Regenwasser und ähnlichen Flüssigkeiten.Die Pumpe hat eine doppelte Wellendichtung bestehend aus zwei Lippenringdichtungen mit Fett dazwischen.Die Pumpe hat ein Außengehäuse, das eine kontinuierliche Kühlung des Motors durch die gepumpten Flüssigkeit gewährleistet. Die Rotorachse arbeitet in zwei wartungsfreien Kohlenstofflagern, die durch die gepumpten Flüssigkeit gekühlt werden.Der Motor ist gefüllt mit einer ungiftigen Motorflüssigkeit. Flüssigkeit: Temperaturbereich der Flüssigkeit:0 .. 50 °CTechnische Daten:Maximale Partikelgröße:10 mmMaterialien:Pumpengehäuse:EdelstahlPumpengehäuse:DIN W.-Nr. 1.4301Pumpengehäuse:AISI 304Laufrad:EdelstahlLaufrad:DIN W.-Nr. 1.4031Laufrad:AISI 304Installation:Pumpenauslass:Rp 1 1/4Maximale Installationshöhe:10 mElektrische Daten:Leistungsaufnahme - P1:480 WNennspannung:1 x 220-230 VNennstromstärke:2,3 AKondensatorgröße - Lauf:F8 /400 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC85):F Kabellänge :10 mTyp des Kabelsteckers : SchukoAndere:Nettogewicht :7 kgBruttogewicht :7,8 kgVersandvolumen :0,013 m3

UP 15-14 B PMThe high efficiency Coomfort PM range is a product for domestic hotwater recirculation in 1 and 2 family houses.The motor is a single-phase, 2-pole, hysteresis, permanent-magnet motor in conformity with the EMCdirective.Characteristics and benefits:* Unique AUTOADAPT saves up to 50% heatenergy and 87% motor energy compared with a standard pump in continuous operation* Flushing function* Automatic legionella operation (if supported from the system)* Automatic weekend and vacation function* Temperature control optional* Continuous operation optional* Fast and simple electrical installation due to the million times trusted ALPHA plug* Easy to clean and lime insensitive spheric rotor* Application area up 14°dH water hardness* Wearless operation due to liquid lubricated bearing* No leakage risk due to a static seal* Easy maintenance and cleaning by easy-to-separated motor head that fits on all standard circulation pump housings* Korrosion resistant pump housing in brass* Due to impedance protected motor no motor protection necessary* No additional installation costs due to integrated non return and stop valve in the pump housingLiquid:Liquid temperature range:2 .. 95 °CTechnical:TF class:95Approvals on nameplate:VDE,GS,CEMaterials:Pump housing:Brass MS 68Impeller:Stainless steel, EPDM, PPO, PTFE, GraphitInstallation:Maximum operating pressure:10 barPipe connection:Rp 1/2Port-to-port length:80 mmElectrical data:Max. power input:8 WRated voltage:1 x 230 VCurrent in speed 3:0.07 ACapacitor size - run:0.6 FEnclosure class (IEC 34-5):IP44Insulation class (IEC 85):FOthers:Net weight:1 kgGross weight:1.12 kgShipping volume:0.003 m3

SOLOLIFT2 C-3Sololift2 C-3 is a small, compact automatic lifting station suitable for pumping of greywater (w/o faeces) off places in private dwellings where wastewater cannot be led directly to the sewer by means of a natural downward slope.Sololift2 C-3 is typically used for:• cabinet showers, washbasins, bath tubs, washing machines (max. 90°C) and dishwashers in basements below sewer level or in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Sololift2 C-3 is suitable for installation under a washbasin or particularly for confined space conditions in prewall constructions and built-in cabinets. Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.The compact lifting station is equipped with- Cable with or without plug (see technical data)- Horizontal or vertical faste

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Die ALPHA2 ist in der Lage, den harten Bedingungen in einem Heizsystem standzuhalten, und mit vier neu hinzugefügten Funktionen wurde sie noch robuster: Robuster Start: Befreit die Pumpe am Anfang der Heizsaison von Verunreinigungen. Sommermodus: Einstellung der Leistung der Pumpe im Sommer auf die wärmere Außentemperatur - für zusätzliche Energieeffizienz. Magnetitbeständigkeit: Stellt sicher, dass keine kleinen Metallteile in den wichtigen Teilen der Pumpe stecken bleiben, wenn sie magnetisiert sind. Trockenlaufschutz: Stellt sicher, dass die Pumpe niemals ohne Flüssigkeit im System läuft - hinzu kommt eine unübertroffene Energieeffizienz, einfache Installation und die Tatsache, dass ALPHA2 sowohl Ihre Heizanforderungen als auch bis zu 90 % Ihrer Klimaanforderungen abdeckt.Die GRUNDFOS ALPHA2 eignet sich für:Systeme mit konstantem oder variablem DurchflussEinrohrsystemeZweirohrsystemeFußbodenheizungWarmwasser-ZirkulationssystemeSysteme mit Nachtabsenkung erforderlichMerkmale und VorteileBessere Leistung bei marktführender Effizienz (EEI0.15) in einem kompakteren DesignNeuer Durchflussmesser zur Fehlerbehebung und zum AusgleichAUTOADAPT wählt beste Leistungskurve für Effizienz und KomfortInnovativer Stecker vereinfacht PumpenanschlussIsolierschalen enthalten.

ALPHA2 is able to withstand the tough conditions in a heating system, and with four newly added features, it just got even tougher:Robust start-up:Shakes free any impurities before the pump starts at the beginning of the heating season.Summer mode:Adjustment of the pump’s performance in the summer to the warmer temperature outside – giving customers extra energy efficiency.Magnetite resistance:Ensures that no small pieces of metal get stuck in the pump’s vital parts when they are magnetised.Dry-running protection:Makes sure the pump never runs without liquid in the system - add to that unrivalled energy efficiency, easy installation and the fact that ALPHA2 covers both your heating demands and up to 90 % of your air-conditioning and cooling demands.The GRUNDFOS ALPHA2 is suitable for:• Systems with constant or varying flow• One pipe systems• Two pipe systems• Underfloor-heating• Domestic hot-water recirculation• Systems where night setback is required.Features and benefits• Better performance with market leading efficiency (EEI0.15) in a more compact design• New flow meter for trouble-shooting and balancing• AUTOADAPT selects best performance curve for efficiency and comfort• Innovative plug simplifies pump connection• Insulation shells included.

Die Premium-Wahl, wenn die Systemsteuerung und Überwachung entscheidend sind. Die MAGNA3 unterstützt Feldbus durch optionale CIM-Module und verfügt über ein TFT-Display zur intuitiven Konfiguration der intelligenten Funktionen. Anwendungen: Heizung, Klimatisierung, Pumpendesigns: Dosenrotor Technische Daten: Maximaler Kopf: 18,88 m Flüssigkeitstemperatur: -10 .. 110 ° C Maximaler Durchfluss: 76,6 m3 / h P max : 16 bar

Die hocheffiziente Coomfort PM-Serie ist ein Produkt für die Warmwasserzirkulation in Ein- und Zweifamilienhäusern. Der Motor ist ein einphasiger, 2-poliger, Hysterese-, Permanentmagnetmotor in Übereinstimmung mit der EMC-Richtlinie. Merkmale und Vorteile: * Einzigartige AUTOADAPT spart bis zu 50% Wärmeenergie und 87% Motorenergie im Vergleich zu einer Standardpumpe im Dauerbetrieb * Spülfunktion * Automatischer Legionellenbetrieb (falls vom System unterstützt) * Automatische Wochenend- und Urlaubsfunktion * Temperaturregelung optional* Dauerbetrieb optional* Schnelle und einfache elektrische Installation aufgrund des millionenfach bewährten ALPHA-Steckers* Leicht zu reinigender und kalkunempfindlicher sphärischer Rotor* Anwendungsbereich bis 14°dH Wasserhärte* Verschleißfreier Betrieb durch flüssigkeitsgeschmiertes Lager* Kein Leckagerisiko durch eine statische Dichtung.* Einfache Wartung und Reinigung durch leicht abnehmbaren Motorkopf, der auf alle Standard-Umwälzpumpengehäuse passt.* Korrosionsbeständiges Pumpengehäuse aus Messing.* Aufgrund des impedanzgeschützten Motors kein Motorschutz erforderlich.* Keine zusätzlichen Installationskosten aufgrund integrierter Rückschlagklappe und Absperrventil im Pumpengehäuse.Flüssigkeit:Flüssigkeitstemperaturbereich:2 .. 95 °CTechnisch:TF-Klasse:95Zulassungen auf Typenschild:VDE, GS, CEMaterialien:Pumpengehäuse:Messing MS 68Laufrad:Edelstahl, EPDM, PPO, PTFE, GraphitInstallation:Höchstdruckbetrieb:10 barRohranschluss:G 1 1/4Port-to-Port-Länge :110 mmElektrische Daten:max. Leistungsaufnahme :8 WRated voltage :1 x 230 VStrom in Geschwindigkeit 3 :0.07 AKondensatorgröße - Laufzeit :0.6 FSchutzart (IEC 34-5):IP44Isolationsklasse (IEC85):FOthers:Nettogewicht :1.35 kgBruttogewicht :1.51 kgVersandvolumen:0.003 m3

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 65-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

ALPHA2 is able to withstand the tough conditions in a heating system, and with four newly added features, it just got even tougher:Robust start-up:Shakes free any impurities before the pump starts at the beginning of the heating season.Summer mode:Adjustment of the pump’s performance in the summer to the warmer temperature outside – giving customers extra energy efficiency.Magnetite resistance:Ensures that no small pieces of metal get stuck in the pump’s vital parts when they are magnetised.Dry-running protection:Makes sure the pump never runs without liquid in the system - add to that unrivalled energy efficiency, easy installation and the fact that ALPHA2 covers both your heating demands and up to 90 % of your air-conditioning and cooling demands.The GRUNDFOS ALPHA2 is suitable for:• Systems with constant or varying flow• One pipe systems• Two pipe systems• Underfloor-heating• Domestic hot-water recirculation• Systems where night setback is required.Features and benefits• Better performance with market leading efficiency (EEI0.15) in a more compact design• New flow meter for trouble-shooting and balancing• AUTOADAPT selects best performance curve for efficiency and comfort• Innovative plug simplifies pump connection• Insulation shells included.

Unilift AP35B.50.06.3.VSubmersible effluent pumpVertical single-stage stainless steel submersiblepump with integrated submersible 3-phasemotor. The pump is fitted with ring stand and carryinghandle and is supplied with a 5 m mainscable. The impeller is a VORTEX impeller for35 mm free passage suitable for pumpingsurface water, groundwater, wastewater andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil. The motor is insulation class F and has long-life deep-groove greased-for-life ball bearings.The pump has R 2' discharge port and is readyfor installation either free-standing or on anauto-coupling system. Liquid:Maximum liquid temperature:40 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:R 2'Maximum installation depth:7 mElectrical data:Power input - P1:1 kWRated voltage:3 x 400 VRated current:1.55 ACos phi - power factor:0,89Rated speed:2830 rpmEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:5 mType of cable plug:NONEOthers:Net weight:8.22 kg

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Kit,Shaft seal CR/N32/45/90/120/150 HQQE

3 mehrstufige, tauchfähige Pumpe für die Wasserversorgung im Haushalt, Flüssigkeitstransfer in Tanks, Bewässerung und Umweltanwendungen konzipiert. Die Pumpe verfügt über schwimmende Laufräder, von denen jedes ein eigenes Wolframkarbid-/Keramiklager hat.

Unilift KP 150 M 1 Tauchpumpe Vertikale einstufige Edelstahl-Tauchpumpe mit vertikalem Auslass und integriertem einphasigen Tauchmotor der Isolationsklasse F mit thermischem Überlastschutz. Die Pumpe ist mit einem Saugkorb, einem Tragegriff ausgestattet und wird mit einem 10 mm Netzkabel geliefert. Der Laufrad ist ein halboffenes Laufrad für einen freien Durchgang von 10 mm und eignet sich zum Pumpen von Grundwasser, Oberflächenwasser, Regenwasser und ähnlichen Flüssigkeiten. Die Pumpe hat eine doppelte Wellendichtung bestehend aus zwei Lippenringdichtungen mit Schmierfett dazwischen. Die Pumpe hat ein Außengehäuse, das eine kontinuierliche Kühlung des Motors durch die gepumpten Flüssigkeit gewährleistet. Der Rotorwellenbetrieb erfolgt in zwei wartungsfreien Kohlenstofflagern, die durch die gepumpten Flüssigkeit gekühlt werden.Der Motor ist gefüllt mit einer ungiftigen Motorflüssigkeit.Flüssigkeit:Flüssigkeitstemperaturbereich:0 .. 50 °CTechnisch:Höchstpartikelgröße:10 mmMaterialien:Pumpengehäuse:EdelstahlPumpengehäuse:DIN W.-Nr. 1.4301Pumpengehäuse:AISI 304Laufrad:EdelstahlLaufrad:DIN W.-Nr. 1.4031Laufrad:AISI 304Installation:Pumpenauslass:Rp 1 1/4Maximale Installationshöhe:10 mElektrische Daten:Eingangsleistung - P1:300 W Nennspannung:1 x 220-230 VNennstrom:1,3 AKondensatorgröße - Laufzeit:8 F/400 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC 85):FLänge des Kabels:10 mTyp des Kabelsteckers : SchukoAndere:Nettogewicht :6,5 kgBruttogewicht :6,5 kgVersandvolumen :0.013 m3

Unilift CC 7 Grundfos Unilift CC Pumpen sind einstufige Tauchpumpen mit einer niedrigen Saugfähigkeit bis zu einem Wasserstand von 3 mm. Die Pumpen sind für das Abpumpen von Regenwasser und Grauwasser ausgelegt, z.B. von Waschmaschinen, Bädern, Spülen usw. aus tiefer gelegenen Teilen von Gebäuden bis zur Kanalisationsebene; Kellern oder Gebäuden, die anfällig für Überschwemmungen sind; Entwässerungsbrunnen; Brunnen für Oberflächenwasser mit Einlässen aus Dachrinnen, Gruben, Tunneln usw.; Schwimmbecken, Teichen oder Springbrunnen. Die Pumpen eignen sich sowohl für den stationären als auch den mobilen Einsatz und arbeiten automatisch. Sie lassen Partikel bis zu ø10 mm passieren.Der Motor verfügt über einen automatischen Überlastschutz und schaltet bei Überlastung ab. Wenn er auf normale Temperatur abgekühlt ist, startet der Motor automatisch wieder.Technische Daten:Höchstpartikelgröße:10 mmMaterialien:Pumpengehäuse:PP 15 GFRad:PPOm 20 GFInstallation:Pumpenauslass:1-1/4'Maximale Installationshöhe:10 mLiquid:Liquid-Temperaturbereich:0 .. 40 °CElektrische Daten:Nennspannung:1 x 220-240 VNennstrom:1,8 AKondensatorgröße - Laufzeit :8 F/450 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC 85):FLänge des Kabels:10 mTyp des Kabelsteckers:SCHUKOAndere:Nettogewicht:4,6 kgBruttogewicht:5,2 kgVersandvolumen:0,168 m3

MAGNA3 40-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 50-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 65-150 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot