PEX-Systeme - Seite 8

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Used for fix of pipe

Quickbox tool for flange

Wallbox for Pex

Manifold for water TEA 4 outlets 15/10 mm fittings

Uponor Smart Aqua tap elbow Q&E NKB DR 15 mm x 12 L= 43 mm.

Nipple in gunmetal Roth 3/4" EURO x 3/4", used with female plastic pipe fitting

WALLOFIX Flansch für Membran zur Wanddose

Plaserboard kit to wallbox

Werkzeug für Flansch an der Wand

Wallofix Installationswerkzeug zur Markierung der Einstecktiefen und Montage sowie Montage in der Ebene mit einem Mittelabstand

EPDM 120x120 - ø54

Used for connection between Pex and pipe, valves etc. with thread

Termination box, including Q&E termination elbow in DR-brass,white Q&E ring and mounting screws. For water proofconnection with PE-Xa pipes and Uponor conduit in all typesof walls, according to NT VVS 129.

Extra breite Metallhalterung für Uponor Anschlussdosen mit Schraublöchern (D4 mm) - c/c 150 mm. Höhe 70 mm, Breite 360 ​​mm, Dicke 1,25 mm. Zur Installation in Beton, Leichtbeton und Plattenwand. Kann von vorne und hinten an einer Wand montiert werden.

Manifold in gunmetal with push and insert in AISI 316

Roth pipe hooks in length of 60 mm. Drill an 8 mm hole and tap the pipe hook in the hole without raw plugs.

Messingverteiler mit 4 Anschlüssen für Wasser- und Heizsysteme.

Manifold in gunmetal with push and insert in AISI 316

Used for pex pipe

Adapter für die Verwendung mit dem PPM-Verteilersystem. Maximaler Druck: 10 bar Maximale Temperatur: 70°C Die Montage des Adapters und des Verteilers erfolgt ohne Werkzeug mit einer Bajonettkupplung.

Termination box, including Q&E termination elbow in DR-brass, white Q&E ring and mounting screws. For water proof connection with PE-Xa pipes and Uponor conduit in all types of walls, according to NT VVS 129.

Aufhängeclips für PPM-Verteiler zur Montage im Verteilerschrank. Hergestellt aus PPSU.

Adapter für die Verwendung mit dem PPM-Verteilersystem. Maximaler Druck: 10 barMaximale Temperatur: 70°CDie Montage des Adapters und des Verteilers erfolgt ohne Werkzeug mit einer Bajonett-Kupplung.

Slip coupling, push-fit 15mm stainless steel