PEX-Systeme - Seite 6

Uponor 1025829 Sanitärarmatur

Used for QuickBox in dry wall

Used when installing Pex pipes in push-in fittings.

Used for Roth pushfittings in gunmetal

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

PPM modulares Verteilungsrohrsystem für Trinkwasser in PPSU (Polyphenylsulfon). Mit Bajonettsteckverbindungen, wird mit O-Ring für Außengewinde geliefert. Abzweigungen mit Bajonett-Kupplungssystem, so dass es für mehrere verschiedene Adapter und Übergangsstücke verwendet werden kann. Das Kupplungssystem darf nur mit Ator's PE-Xa Rohren und Q&E-Adaptern oder MLC-Rohren und Druckadaptern verwendet werden.

used for outdoor faucet

Intake Piece for pipe systems with QuickBox

Roth QuickBox®-316 for stonewall,18 mm x 3/4" push, db

Used for For pipe in 20 mm

Used for Pex and CU pipe

Transition from 18 mm to pipe thread.

Transition from 28 mm to pipe thread.

Transition from 28 mm to pipe thread.

Used for Roth Quickskab, manifold cabinet

Fitting in gunmetal for Roth manifold

Fitting in gunmetal for Roth manifold

Uponor 20 mm Rohrhalterung.

Hergestellt von PPSU. Q&E-System nur mit Uponor PE-Xa Rohren verwenden

HENCO VISION connection part to the manifold, angle 26 mm for water, heating and cooling installations Max. 16 bar

HENCO VISION 20 mm Adapterhülse für Verteiler für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

HENCO Druckprüfstopfen 16 mm für Wasser-, Heizungs- und Elektroinstallationen Max. 16 bar

HENCO Druckprüfstopfen 26 mm für Wasser-, Heizungs- und Elektroinstallationen Max. 16 bar

For dry wall, push

For dry wall, push