Entwässerungsprodukte - Seite 32

Wavin PP bend 15° 200mm

Wavin PP sliding sleeve 200mm

Wavin PP plug 160mm. Blue

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Armatur Unidrain 1003, 800 mm Ecke rechts.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

For shower cubicles with open left-hand side, glass screen or similar.

The drain unit has two wall flanges.

Fixture Unidrain 1004 700 mm ohne Flansch.

Outlet-Einheit | Leitung | Ø 75 mm horizontal, inkl. Siphon

Armatur Unidrain 1004 800 mm ohne Flansch.

Rist Unidrain Klassiker mit einer Länge von 700mm.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Complete floor drain against rear wall 700 mm, 10 mm frame, Column grate, 75 mm vertical outlet housing

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Unidrain Armatur 1004, 1000 mm ohne Flansch.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.