Entwässerungsprodukte - Seite 30

Complete floor drain against rear wall 700 mm, 10 mm frame, Column grate, 75 mm vertical outlet housing

The grate is placed on a recessed bearing in the frame, which ensures precise positioning.

Can only be used with ClassicLine frame.

The water trap is removable and can be taken apart for cleaning

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

Abflussgarnitur Unidrain Fritl 3004 300 mm.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Horizontal outlet Ø 75 mm, including water trap.

Two horizontal side inlets, 40 mm, which can be opened as needed. 2 rubber adapters are included so that side inlets can be reduced to 32 mm. Easy access to the removable water trap for cleaning. Meets EN1253 standard and is VA approved.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

NB: PVD-treated surface.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Complete floor drain against rear wall 800 mm, 10 mm frame, Column grate, 75 mm vertical outlet housing

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Wastewater pipesystem GM-X galvanized DN 80x2000 mm

Abwasserrohrsystem GM-X, verzinkt, gebogen DN 50, 87 Grad

Abwasserrohrsystem GM-X, verzinkt, gebogen DN 50, 45 Grad

Wavin PP double sleeve 200mm

Wavin PP bend 88.5° 200mm

Wavin PP plug 110mm, blue

Wavin PP branch pipe 45° 200/110mm

Wavin PP bend 15° 200mm

Wavin PP sliding sleeve 200mm

Wavin PP plug 160mm. Blue

Geberit Elektroschweißband für Ankerpunkt: D=125 mm