Rahmen Unidrain 12 mm.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Rahmen Unidrain 10 mm.

Outlet-Haus Unidrain Ø75 horizontal mit Wassersperre.

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

Vinyl-Abfluss in Edelstahl inklusive Rahmen und Gitter im Modell Säulenlänge 800 mm

Water trap 50 mm water seal. Meets capacity and selfcleaning requirements according to EN 1253 (the panEuropean standard for floor drains) and is VA-approved. The water trap can be removed from the outlet unit and then dismantled for cleaning.

NOTE: Suitable only for outlet unit 1418.0050.

With side drain on the left.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

Rist Unidrain Quadrat 1604 misst 800 mm.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Armatur Unidrain 1003, 800 mm Ecke rechts.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Fixture Unidrain 1004 700 mm ohne Flansch.

Armatur Unidrain 1004 800 mm ohne Flansch.

Can be freely positioned against the back wall, independent of any side walls.

The drain unit has one wall flange.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Unidrain Armatur 1004, 1000 mm ohne Flansch.

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

ClassicLine Rost - Linie - Edelstahl, gebürstet: Anniversario, 800 mm. ClassicLine Anniversario ist ein Rost, der anlässlich des 10-jährigen Jubiläums von unidrain® im Jahr 2013 eingeführt wurde. Der Jubiläumsrost bringt den klassischen Rost näher an die exklusive HighLine-Serie und besteht aus gebürstetem Edelstahl, der zum Rahmen passt.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.