Unidrain - Seite 8

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Unidrain water trap for 155012613 and 155012612.

Rahmen Unidrain 12 mm.

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

The set consists of the Custom base, rail, heightener set and screws.

The set must be assembled before installation.

Glue your own floor tile to the base, to complete the solution.

The Custom solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit.

Special glue for adhesion of your own tile and 10 x 6-mm spacers to use for installation are also included.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Vinyl-Abfluss in Edelstahl inklusive Rahmen und Gitter im Modell Säulenlänge 800 mm

Rist Unidrain Klassik mit einer Länge von 1000 mm.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

ReFrame 7012 Seifenablage und Duschabzieher in Messing. Auch erhältlich in gebürstetem Stahl, poliertem Stahl, Kupfer und Schwarz.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

ShowerLine has a built-in slope, so that the floor in the shower cubicle slopes correctly by 2% down towards the floor drain. For added wetroom safety, the shower cubicle is framed by flanges on three sides.

The shower screen is mounted in the track on the fixed module, to eliminate the risk of working loose over time. Combine with: outlet unit, frame, grating/panel and shower screen.

Montageprofil für 1004.1000 mit einer Dicke von 22 mm.

ClassicLine corner drain kit - vertical Ø 75, Column, H 10 mm. The drain kit is the simple solution that contains all the necessary parts for a unidrain® ClassicLine system. The solution is composed of the best-selling products, which can therefore meet the needs of most bathrooms. The solution is available in lengths of 700, 800, 900 and 1000 mm and as a corner solution, and includes: ClassicLine grate (Column), ClassicLine frame (H 10 mm), wooden slats, drainage fixture (1004 with back flange) and outlet housing (Ø75mm vertical incl. trap).

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles with open left-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.