PEX-Systeme - Seite 2

HENCO VISION Messing-Nippeladapter 26 x 3/4 für Verteilerrohre für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

HENCO VISION Messinghülse Adapter 20 x 1/2 für Verteilerrohre für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Used for QuickBox in plate walls.Remember to order Ø4 x 60 mm screws to fasten the junction boxes, use 2-4 screws per. junction box.

HENCO VISION 26 mm Adapternippel für Verteiler für Wasser-, Heizungs- und Kühlanlagen Max. 16 bar

Used for connection between Pex/Alu and pipe, valves etc. with thread

Used for connection between Pex/alu and pipe, valves etc. with thread

Vereinige Cutter für Multibox

Fitting in gunmetal for Roth manifold

Wavin RADIATOR TRIM SET 15X1/2 F/PEX SHORT

Uponor 19 mm Installations-Set

Hergestellt aus Polypropylen. Für Bodendurchführungen für Heizkörper. Passt in leere Rohre mit Abmessungen von 25/20. C/C 40 mm. Kann mit einem Abstandshalterblock modifiziert werden.

Hergestellt von PPSU. Q&E-System nur mit Uponor PE-Xa-Rohren zu verwenden

Hergestellt von PPSU. Q&E-System nur mit Uponor PE-Xa-Rohren zu verwenden

Manifold cabinet for Roth floorheating manifold

Manifold cabinet for Roth floorheating manifold

Used for pipe in 20 mm

Rohrschelle zur Befestigung von Rohren, 25mm. UniteSchrauben inklusive

Schiene für PEX wird für PEX-Rohre und Fußbodenheizung vor dem Gießen verwendet. Mitteabstand: 50 mm. Inklusive Trennung und 2 separaten Rohren.

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc•dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc•flexible, blackDimensionsPress connectors and pipes•Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63•Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations•Operating temperature max. 70 °C•Operating pressure max. 1.0 MPaHeating installations•Operating temperature max. 80 °C•Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Uponor Kupplungsbox doppelt M4 15X1/2

Paar Abschlusskästen inklusive zwei Q&E-Abschlussecken aus DR-Messing mit weißen Q&E-Ringen, Metallmontagehalterung für die Montage c/c 150mm und Montageschrauben. Für wasserdichte Verbindungen mit PE-Xa-Rohren und Uponor-Kanälen in allen Arten von Wänden gemäß NT VVS 129.

Used for assembly of pipe, pipe in pipe

Used for For pipe in 15 mm

Support bushes for Pex and insert fittings.