Druckrohre und Armaturen - Seite 57

Viega 2315

Viega 2315.1

Sanpress Inox Connection screw fitting with SC-Contur- steel non-corroding- press connection, G-thread- flat sealingComponentsEPDM sealing element, EPDM flat seal, union nut screw fitting d: 18, G: 34

Viega 2612

Viega 2311.1

Sanpress Inox T-Stück mit SC-Contur- Stahl nicht korrodierend - PressverbindernKomponentenEPDM-Dichtelemente, VdS-Zertifizierungd1: 42, d2: 22, d3: 42

Sanpress Inox Sliding coupling with SC-Contur- steel non-corroding- press connectors ComponentsEPDM sealing elementsd: 15

Viega 2311.1

Viega 2416.1

Sanpress Inox Adapter with SC-Contur- steel non-corroding- press connection, R-thread ComponentsEPDM sealing element, polygon, VdS certificationd: 54, R: 2

Viega 2416.1

Viega 2312.1

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Viega 2416

Viega 2426.1

Viega 2426.1

Viega 2611

Viega 2612

Prestabo Sliding coupling with SC-Contur - galvanised non-alloyed steel - press connectors Components EPDM sealing elementsd: 54(VdS certification)

Press connector system with press connectors and pipes made of copper in acc. with EN 1057 and DVGW worksheet GW 392 suitable for:•Gases in acc. with DVGW G 260 in gas installations in acc. with DVGW-TRGI 2008 (DVGW worksheet G 600) / DVFG-TRF 2012•Liquid gas in the gas phase for domestic and commercial applications, tested in acc. with DVGW worksheet G 5614•Heating oil pipelines for heating oil in acc. with DIN 51603-1•Diesel fuel pipelines for diesel fuel, as suction and pressure pipelines in acc. with EN 590 in consideration of the general technical approval Z-38.4-71Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet G 5614, point 4.4.1, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingYellow dot, yellow rectangle and inscription »Gas MOP 5 / GT1«Sealing elementsHNBR, yellowDimensions/MaterialStandard sizes: d 12, 15, 18, 22, 28, 35, 42, 54 made of copperXL sizes: d 64.0 made of copperPress connectors with threaded connection d 12–54 made of gunmetalXL press connectors with threaded connection d 64.0 made of copperAreas of applicationNatural gas/Liquid gasHeating oil/Diesel fuel (d 12–54)NoteOnly Viega copper and gunmetal press connectors, which are marked with a yellow rectangle and have the inscription »Gas MOP 5 / GT1« are permitted for use in installations for gas, heating oil and diesel fuel systems!Use of the system for application areas and media other than those described here must be agreed with Viega Service Center through a material request.Operating conditionsGas and liquid gas systems•Operating temperature -20 °C up to +70 °C•Operating pressure max. 0.5 MPa•Operatin

Profipress Cap with SC-Contur- copper - press connection Components EPDM sealing elements

Viega 4211

Viega 1116.1

Viega 2615.1

Megapress-Adapter mit SC-Contur für Trinkwasserinstallation - Stahlrohre gemäß DIN EN 10220/10255 mit Verzinkung gemäß DIN EN 10240 - Rotguss oder Siliziumbronze - PressverbindungenKomponentenEPDM-Dichtelement, Schneidring, TrennringDN: 20, D: 34, d: 22