Druckrohre und Armaturen

Prestabo Coupling with SC-Contur - galvanised non-alloyed steel - press connectors Components EPDM sealing elementsd: 18

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Sanpress Inox XL T-piece with SC-Contur- steel non-corroding- press connectors, Rp-thread- polygonComponentsEPDM sealing elements, cutting rings, separator rings, VdS certificationd1: 88.9, Rp: 34, d2: 88.9

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Pressverbindersystem mit nach DVGW-Arbeitsblatt W 534 geprüften Pressverbindern aus Kupfer und Rotguss mit DVGW-Prüfsiegel und Rohren aus Kupfer nach EN 1057 nach DVGW-Arbeitsblatt GW 392.Geeignet für die Trinkwasserinstallation nach DIN 1988.Für die formstabile Unterputz- und Vorwandinstallation von Verteiler- und Steigleitungen im Viega-Komponentenverbund.PressverbinderAlle Größen mit SC-Contur - Verbindungen, die unverpresst bleiben, werden beim Befüllen des Systems sichtbar. Die SC-Contur ist zertifiziert und erfüllt die Anforderungen des DVGW-Arbeitsblattes W 534, Punkt 12.14, Verbindungen mit erzwungener Dichtheit.Viega gewährleistet bei Dichtheitsprüfungen mit Wasser die Erkennbarkeit unverpresster Verbindungen im Druckbereich 0,1 MPa-0,65 MPa, bei trockener Dichtheitsprüfung mit Druckluft oder Edelgasen von 22 hPa-0,3 MPa.KennzeichnungGrüner Punkt auf der PressverbindungDichtelementeEPDM, schwarz (Ethylen-Propylen-Dien-Monomer-Kautschuk), bis 110 °C

For heating water, For cooling water without antifreeze agent, For cooling water with antifreeze agent, For remote network heating water 120 °C, For extinguishing water (wet),For sprinklers (wet), For compressed air (oil purity class 0–3), For inert gases (e.g. nitrogen), For technical building systems, industry and shipbuilding, Application overview: Geberit Mapress Carbon Steel

For heating water, For cooling water without antifreeze agent, For cooling water with antifreeze agent, For remote network heating water 120 °C, For extinguishing water (wet),For sprinklers (wet), For compressed air (oil purity class 0–3), For inert gases (e.g. nitrogen), For technical building systems, industry and shipbuilding, Application overview: Geberit Mapress Carbon Steel

Sanpress Adapter with SC-Contur- gunmetal or silicium bronze- press connection, Rp-threadComponentsEPDM sealing element, polygon, VdS certification d: 54, Rp: 2

Profipress G Coupling with SC-Contur- copper - press connectors Components HNBR sealing elements d: 22

Sanpress Inox Coupling with SC-Contur- steel non-corroding - press connectorsComponents EPDM sealing elements, cutting rings, separator rings d: 76,1(VdS certification)

Sanpress Inox Reducer with SC-Contur- steel non-corroding- plug-in end, press connectionComponentsEPDM sealing element, VdS certificationd1: 42, d2: 28

Profipress G Adapter with SC-Contur- gunmetal- press connection, R-threadComponentsHNBR sealing element, polygond: 22, R: 34

Profipress T-piece with SC-Contur- copper- press connectorsComponentsEPDM sealing elements d1: 22, d2: 18, d3: 22

Profipress Coupling with SC-Contur- copper- press connectorsComponents EPDM sealing elementd: 28(VdS certification)

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Sanpress Inox Wall plate with SC-Contur- steel non-corroding- press connection, Rp-threadComponentsEPDM sealing element, fixing flanged: 15, Rp: 12

Press connector system with press connectors and pipes made of stainless steel material Nos. 1.4401 and 1.4521 in acc. with DIN EN 10088, DIN EN 10312, DVGW worksheet GW 541, system certification for connectors and pipes in acc. with DVGW worksheet W 534, for drinking water installations in acc. with DIN 1988. For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-die

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectorsComponentsEPDM sealing elements, VdS certification d1: 28, d2: 28, d3: 28

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectorsComponentsEPDM sealing elements, VdS certificationd1: 35, d2: 35, d3: 35

Sanpress Inox T-piece with SC-Contur- steel non-corroding- press connectorsComponentsEPDM sealing elements, VdS certificationd1: 42, d2: 42, d3: 42

Sanpress Plug-in piece- gunmetal or silicium bronze- plug-in end, R-threadComponentsPolygon d: 18, R: 12

Press connector system with press connectors made of copper and gunmetal tested in acc. with DVGW worksheet W 534 with DVGW test seal and pipes made of copper in acc. with EN 1057 in acc. with DVGW worksheet GW 392.Suitable for drinking water installations in acc. with DIN 1988.For dimensionally stable concealed and pre-wall installations of manifold and riser pipes in Viega component assembly.Press connectorsAll sizes with SC-Contur – connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa–0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa–0.3 MPa.MarkingGreen dot on the press connectionSealing elementsEPDM, black (ethylene-propylene-dien-monomer rubber), up to 110 °C

Profipress Sliding coupling with SC-Contur- copper- press connectors ComponentsEPDM sealing elements d: 18