Pumpen - Seite 3

UP 15-14 BA PMThe high efficiency Coomfort PM range is a product for domestic hotwater recirculation in 1 and 2 family houses.The motor is a single-phase, 2-pole, hysteresis, permanent-magnet motor in conformity with the EMCdirective.Characteristics and benefits:* Unique AUTOADAPT saves up to 50% heatenergy and 87% motor energy compared with a standard pump in continuous operation* Flushing function* Automatic legionella operation (if supported from the system)* Automatic weekend and vacation function* Temperature control optional* Continuous operation optional* Fast and simple electrical installation due to the million times trusted ALPHA plug* Easy to clean and lime insensitive spheric rotor* Application area up 14°dH water hardness* Wearless operation due to liquid lubricated bearing* No leakage risk due to a static seal* Easy maintenance and cleaning by easy-to-separated motor head that fits on all standard circulation pump housings* Korrosion resistant pump housing in brass* Due to impedance protected motor no motor protection necessary* No additional installation costs due to integrated non return and stop valve in the pump housingLiquid:Liquid temperature range:2 .. 95 °CTechnical:TF class:95Approvals on nameplate:VDE,GS,CEMaterials:Pump housing:Brass MS 68Impeller:Stainless steel, EPDM, PPO, PTFE, GraphitInstallation:Maximum operating pressure:10 barPipe connection:Rp 1/2Port-to-port length:80 mmElectrical data:Max. power input:8 WRated voltage:1 x 230 VCurrent in speed 3:0.07 ACapacitor size - run:0.6 FEnclosure class (IEC 34-5):IP44Insulation class (IEC 85):FOthers:Net weight:1 kgGross weight:1.12 kgShipping volume:0.003 m3

Pumpe Ecowatt 1*230V

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Mit ALPHA2 GO kann der Installateur nun den Großteil aller Stand-alone-Umwälzpumpen und nahezu 70% der Pumpen ersetzen, die in Fernwärmeunits, Gasheizkesseln und Wärmepumpen nach 2015 integriert sind. Einbaumaß: 180mm

Hauswasserwerkpumpe liefert 1300 W Leistung mit bis zu 4.8 bar Druck und 4500 l/t Förderleistung für automatische Wasserversorgung, Gartenbewässerung und Klarwasserförderung.

Metabo HWW 4500/25 INOX ist für energiesparende, geräuscharme Wasserbereitstellung mit Druckbehälter und tankmontiertem Druckschalter ausgelegt, der bei steigendem Wasserbedarf automatisch einschaltet.

• Wartungsfreier Kondensatormotor mit Überlastschutz gegen Überhitzung
• Robustes Pumpengehäuse aus Edelstahl und hochwertiges Gleitringdichtungssystem für lange Lebensdauer
• Separate Wasser-Einfüllöffnung für einfache Bedienung
• Werkzeuglos abnehmbarer Wasserablassstopfen als Frostschutz
• Geeignet für Gartenbewässerung mit 1 bis 3 Regnern
• Ausgelegt für Einphasen-Wechselstrom

Zuverlässiger, automatischer Druck und Durchfluss machen die tägliche Wasserversorgung und Bewässerung komfortabler und gleichmäßiger.

Die hocheffiziente Grundfos COMFORT PM Pumpe für die Warmwasserzirkulation in Ein- und Zweifamilienhäusern ist für bleifreies Trinkwasser geeignet und wird von einem hocheffizienten, einphasigen Permanentmagnetmotor angetrieben. Der integrierte digitale Timer wurde für die Warmwasserzirkulation in Systemen mit Warmwassertanks oder Plattenwärmetauschern zur Warmwasserproduktion entwickelt. Der Timer ermöglicht es Ihnen, die Betriebszeiten der Pumpe anzupassen, um optimalen Komfort bei gleichzeitiger Senkung der Energiekosten zu gewährleisten. Merkmale und Vorteile:• Digitale Timer-Funktion zur Anpassung der Betriebszeiten der Pumpe.• Dauerbetrieb kann für Inbetriebnahme der Pumpe oder 24-Stunden-Sofortduschen und Wasserhähne eingestellt werden.• Schnelle und einfache elektrische Installation aufgrund des 1,5 m langen Kabels inklusive Netzstecker.• Trockenlaufschutz schützt die Pumpe vor Trockenlauf während des Startvorgangs und des normalen Betriebs.• Leicht zu reinigender und robuster kalkresistenter sphärischer Rotor.• Geräuschloser Betrieb durch flüssigkeitsgeschmiertes Lager.• Kein Leckagerisiko durch eine statische Dichtung.• Einfache Wartung und Reinigung durch den leicht abnehmbaren Pumpenkopf.• Ein Pumpenkopf für den Service im Van, passt auch fast alle Konkurrenzpumpengehäuse an .• Korrosionsbeständiges bleifreies Messingpumpengehäuse.• Kein zusätzlicher Motorschutz erforderlich aufgrund integrierter Motorelektronik.• BXDT-Varianten enthalten Armaturen mit integriertem Rückschlagventil und Absperrventil.

Unilift CC 7 Grundfos Unilift CC Pumpen sind einstufige Tauchpumpen mit einer niedrigen Saugfähigkeit bis zu einem Wasserstand von 3 mm. Die Pumpen sind für das Abpumpen von Regenwasser und Grauwasser ausgelegt, z.B. von Waschmaschinen, Bädern, Spülen usw. aus tiefer gelegenen Teilen von Gebäuden bis zur Kanalisationsebene; Kellern oder Gebäuden, die anfällig für Überschwemmungen sind; Entwässerungsbrunnen; Brunnen für Oberflächenwasser mit Einlässen aus Dachrinnen, Gruben, Tunneln usw.; Schwimmbecken, Teichen oder Springbrunnen. Die Pumpen eignen sich sowohl für den stationären als auch den mobilen Einsatz und arbeiten automatisch. Sie lassen Partikel bis zu ø10 mm passieren.Der Motor verfügt über einen automatischen Überlastschutz und schaltet bei Überlastung ab. Wenn er auf normale Temperatur abgekühlt ist, startet der Motor automatisch wieder.Technische Daten:Höchstpartikelgröße:10 mmMaterialien:Pumpengehäuse:PP 15 GFRad:PPOm 20 GFInstallation:Pumpenauslass:1-1/4'Maximale Installationshöhe:10 mLiquid:Liquid-Temperaturbereich:0 .. 40 °CElektrische Daten:Nennspannung:1 x 220-240 VNennstrom:1,8 AKondensatorgröße - Laufzeit :8 F/450 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC 85):FLänge des Kabels:10 mTyp des Kabelsteckers:SCHUKOAndere:Nettogewicht:4,6 kgBruttogewicht:5,2 kgVersandvolumen:0,168 m3

MAGNA3 65-150 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Produktname: Kabelhalterung für 2 Schwimmerschalter

Pump for Water in one family houses

Pump for Water in one family houses

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Salus kabelstik til MP280A og MP200A cirkulationspumper Produkt beskrivelse: Salus MPPlug. Kablestik til Salus MP280A og MP200A cirkulationspumper

MAGNA3 65-60 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

SOLOLIFT2 WC-3Sololift2 WC-3 is a small, compact automatic lifting station suitable for pumping of wastewater off places in private dwellings where wastewater cannot be led directly to the sewer by means of a natural downward slope.Sololift2 WC-3 is suitable for pumping wastewater from a toilet containing toilet paper and faeces with additional connections on the lid and to the sides of the tank for e.g. washbasin, shower or bidet.The pumping of liquids containing other material may cause faults and limit the scope of guarantee.Sololift2 WC-3 is typically used to dewater:• toilet, washbasin, shower and bidet in basements below sewer level,in connection with the renovation or modernisation of existing buildings, where the location may be remote from the main soil pipe so that a natural slope cannot be established.Extremely low switching levels for lowest construction heights, advantageously in case of connection of a shower receptor.The compact lifting station

Unilift AP12.40.04.A1Submersible drainage pump typeVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase totally enclosed motorin insulation class F with thermal overloadprotection. The pump is fitted with suction strainer and level switch for automatic start and stop.The impeller is a SEMI OPEN impeller for12 mm free passage suitable for pumpinggroundwater, surface water, rain water andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil.The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings.The pump is ready for use as it is fitted withcarrying handle and is supplied with a10 m mains cable. The mains cable is ofthe plug type with glass sealing compound in thesocket to prevent penetration of humidity intothe stator windings.Liquid:Liquid temperature range:0 .. 55 °CTechnical:Type of impeller:SEMI OPENMaximum particle size:12 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:Rp 1 1/2Maximum installation depth:10 mElectrical data:Type of motor:PSCPower input - P1:0.7 kWRated voltage:1 x 230 VRated current:3 ACos phi - power factor:0,99Rated speed:2770 rpmCapacitor size - run:12 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug: SchukoOthers:Net weight:11 kgGross weight:11.5 kg

Die UPM3 Hybrid-Pumpe wird typischerweise in Fußboden- oder Fernheizungen eingesetzt. Diese UPM3 Hybrid ist ein Ersatzteil, das als Ersatz für andere Grundfos UPM3-Varianten verwendet werden kann. Es kann jedoch speziell entworfene Pumpenhäuser im UPM3-Portfolio geben, in denen der Pumpenkopf nicht passt. Aber diese Pumpenhäuser werden nicht in typischen Fernheizungsanlagen, Fußbodenheizungsschaltungen und dergleichen gefunden. Die UPM3 PH Hybrid enthält alle Einstellungen und deckt daher alle UPM3-Produktvarianten ab. Der Schnellstartleitfaden in der Produktverpackung veranschaulicht die verschiedenen Einstellungen. Die UPM3 PH Hybrid bietet auch eine Steuerung über externes Signal: PHW und Wärme. Dies basiert auf einer 7-m-Variante, aber durch Ändern der Pumpeneinstellung können Sie die maximale Kurve von 4 m-, 5 m- und 6 m-Pumpenversionen erreichen.

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from •washing machines, baths, sinks, etc. from low-lying parts of buildings up to sewer level•cellars or buildings prone to flooding•draining wells•wells for surface water with inlets from roof gutters, pits, tunnels, etc.•swimming pools, ponds or fountains.The pumps are suitable for both stationary and portable use. They are for automatic operation. The pumps allow free passage of particles up to ø10 mm. The motor incorporates automatic overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically. Technical: Maximum particle size: 10 mm Materials: Pump housing: PP 15 GF Impeller: PPOm 20 GF Installation: Pump outlet: 1.1/4 Maximum installation depth: 10 m Liquid: Pumped liquid: Any Newtonian liquid Liquid temperature range: 0 .. 40 °C Density: 998.2 kg/m3 Electrical data: Mains frequency: 50 Hz Rated voltage: 1 x 220-240 V Rated current: 1.8 A Capacitor size - run: 8 F/450 V Enclosure class (IEC 34-5): IP68 Insulation class (IEC 85): F Length of cable: 10 m Type of cable plug: SCHUKO

Unilift KP 250 M 1Submersible drainage pumpVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase canned motor ininsulation class F with thermal overloadprotection. The pump is fitted with a suction strainer, acarrying handle and is supplied with a 10 mmains cable.The impeller is a semi-open impeller for 10 mmfree passage suitable for pumping groundwater,surface water, rain water and similar liquids.The pump has a double shaft seal consisting oftwo lip seals with grease in-between.The pump has an outer casing ensuring continuouscooling of the motor by the pumped liquid.The rotor shaft operates in two maintenance-freecarbon bearings cooled by the pumped liquidThe motor is filled with a non-toxic motor liquid.Liquid:Liquid temperature range:0 .. 50 °CTechnical:Maximum particle size:10 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4031Impeller:AISI 304Installation:Pump outlet:Rp 1 1/4Maximum installation depth:10 mElectrical data:Power input - P1:480 WRated voltage:1 x 220-230 VRated current:2.3 ACapacitor size - run:8 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:7 kgGross weight:7.3 kgShipping volume:0.013 m3

Kit, shaft seal H QQEGG KB016S1 30 bar

Entwässerungspumpe Grundfos Unilift AP Basic 35B.50.06.A1.V ist ein Grundfos Unilift AP Basic Modell, gelistet für Entwässerungspumpen-, Abwasserpumpen- und Baupumpen-Anwendungen.

Dieses Produkt wird als afløbspumpe identifiziert, übersetzt als Entwässerungspumpe, wobei die genaue Modellbezeichnung 35B.50.06.A1.V zur präzisen Auswahl unverändert beibehalten wird.

Eine praktische Option, wenn eine spezifische Grundfos Unilift AP Basic Entwässerungspumpe der benötigten Pumpenkategorie zugeordnet werden soll.

Entwässerungspumpe Grundfos Unilift AP 12.40.06.A1 ist ein Grundfos Unilift AP Modell, gelistet für Entwässerungspumpen-Anwendungen.

Diese Pumpe wird durch ihren eindeutigen Grundfos-Modellnamen identifiziert und ist geeignet, wenn eine spezifische Unilift AP Entwässerungspumpe benötigt wird.

Eine gezielte Wahl zum Ersetzen oder Spezifizieren der passenden Grundfos Unilift AP 12.40.06.A1 Entwässerungspumpe.

Mit ALPHA2 GO kann der Installateur nun den Großteil aller Stand-alone-Umwälzpumpen und nahezu 70% der Pumpen ersetzen, die in Fernwärmeunits, Gasheizkesseln und Wärmepumpen nach 2015 integriert sind. Einbaumaß: 130mm

Tauchpumpe Grundfos UNILIFT KP 150 A-1 ist eine Keller- und Entwässerungspumpe, die mit einem Schwimmerschalter geliefert wird.

Dieses Grundfos UNILIFT KP Modell ist für den Einsatz als Keller- und Entwässerungspumpe vorgesehen und damit für entwässerungsbezogene Pumpaufgaben geeignet.

Der integrierte Schwimmerschalter unterstützt den Automatikbetrieb für eine praktische Wasserhandhabung.