Die hocheffiziente Grundfos COMFORT PM Pumpe für die Warmwasserzirkulation in Ein- und Zweifamilienhäusern ist für bleifreies Trinkwasser geeignet und wird von einem hocheffizienten, einphasigen Permanentmagnetmotor angetrieben. Der integrierte digitale Timer wurde für die Warmwasserzirkulation in Systemen mit Warmwassertanks oder Plattenwärmetauschern zur Warmwasserproduktion entwickelt. Der Timer ermöglicht es Ihnen, die Betriebszeiten der Pumpe anzupassen, um optimalen Komfort bei gleichzeitiger Senkung der Energiekosten zu gewährleisten. Merkmale und Vorteile:• Digitale Timer-Funktion zur Anpassung der Betriebszeiten der Pumpe.• Dauerbetrieb kann für Inbetriebnahme der Pumpe oder 24-Stunden-Sofortduschen und Wasserhähne eingestellt werden.• Schnelle und einfache elektrische Installation aufgrund des 1,5 m langen Kabels inklusive Netzstecker.• Trockenlaufschutz schützt die Pumpe vor Trockenlauf während des Startvorgangs und des normalen Betriebs.• Leicht zu reinigender und robuster kalkresistenter sphärischer Rotor.• Geräuschloser Betrieb durch flüssigkeitsgeschmiertes Lager.• Kein Leckagerisiko durch eine statische Dichtung.• Einfache Wartung und Reinigung durch den leicht abnehmbaren Pumpenkopf.• Ein Pumpenkopf für den Service im Van, passt auch fast alle Konkurrenzpumpengehäuse an .• Korrosionsbeständiges bleifreies Messingpumpengehäuse.• Kein zusätzlicher Motorschutz erforderlich aufgrund integrierter Motorelektronik.• BXDT-Varianten enthalten Armaturen mit integriertem Rückschlagventil und Absperrventil.

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 50-120 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Unilift CC 7 Grundfos Unilift CC Pumpen sind einstufige Tauchpumpen mit einer niedrigen Saugfähigkeit bis zu einem Wasserstand von 3 mm. Die Pumpen sind für das Abpumpen von Regenwasser und Grauwasser ausgelegt, z.B. von Waschmaschinen, Bädern, Spülen usw. aus tiefer gelegenen Teilen von Gebäuden bis zur Kanalisationsebene; Kellern oder Gebäuden, die anfällig für Überschwemmungen sind; Entwässerungsbrunnen; Brunnen für Oberflächenwasser mit Einlässen aus Dachrinnen, Gruben, Tunneln usw.; Schwimmbecken, Teichen oder Springbrunnen. Die Pumpen eignen sich sowohl für den stationären als auch den mobilen Einsatz und arbeiten automatisch. Sie lassen Partikel bis zu ø10 mm passieren.Der Motor verfügt über einen automatischen Überlastschutz und schaltet bei Überlastung ab. Wenn er auf normale Temperatur abgekühlt ist, startet der Motor automatisch wieder.Technische Daten:Höchstpartikelgröße:10 mmMaterialien:Pumpengehäuse:PP 15 GFRad:PPOm 20 GFInstallation:Pumpenauslass:1-1/4'Maximale Installationshöhe:10 mLiquid:Liquid-Temperaturbereich:0 .. 40 °CElektrische Daten:Nennspannung:1 x 220-240 VNennstrom:1,8 AKondensatorgröße - Laufzeit :8 F/450 VSchutzart (IEC 34-5):IP68Isolationsklasse (IEC 85):FLänge des Kabels:10 mTyp des Kabelsteckers:SCHUKOAndere:Nettogewicht:4,6 kgBruttogewicht:5,2 kgVersandvolumen:0,168 m3

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

MAGNA3 40-100 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remot

Unilift CC 5 Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level.The pumps are designed for pumping rainwater and grey wastewater, e.g. from• washing machines, baths, sinks, etc. from low-lying parts of buildings up to sewer level• cellars or buildings prone to flooding• draining wells• wells for surface water with inlets from roof gutters, pits, tunnels, etc.• swimming pools, ponds or fountains.The pumps are suitable for both stationary and portable use.They are for automatic operation.The pumps allow free passage of particles up to ø10 mm.The motor incorporates automatic overload protection cutting out the motor in case of overload.When cooled to normal temperature, the motor restarts automatically.Technical:Maximum particle size:10 mmMaterials:Pump housing:PP 15 GFImpeller:PPOm 20 GFInstallation:Pump outlet:1.1/4'Maximum installation depth:10 mLiquid:Liquid temperature range:0 .. 40 °CElectrical data:Rated voltage:1 x 220-240 VRated current:0.98 ACapacitor size - run:4 F/450 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):BLength of cable:5 mType of cable plug:SCHUKOOthers:Net weight:4.35 kgGross weight:5 kgShipping volume:0.168 m3

Kit,Shaft seal CR/N32/45/90/120/150 HQQE

3 mehrstufige, tauchfähige Pumpe für die Wasserversorgung im Haushalt, Flüssigkeitstransfer in Tanks, Bewässerung und Umweltanwendungen konzipiert. Die Pumpe verfügt über schwimmende Laufräder, von denen jedes ein eigenes Wolframkarbid-/Keramiklager hat.

Mobiles Produkt zur hydraulischen Abgleich von Heizkörpern in Kombination mit einer ALPHA3-Pumpe und einem Smartphone mit der installierten "Go Balance"-App, die für iOS- und Android-Geräte verfügbar ist. Zur vorübergehenden Montage an der ALPHA3-Pumpe

Unilift AP12.40.06.1 Tauchpumpe Typ Vertikale einstufige Edelstahl-Tauchpumpe mit vertikalem Auslass und integriertem einphasigem, vollständig geschlossenem Motor der Isolationsklasse F mit thermischem Überlastschutz. Die Pumpe ist mit einem Saugkorb ausgestattet.Das Laufrad ist ein HALBOFFENES Laufrad für 12 mm freien Durchgang und eignet sich zum Pumpen von Grundwasser, Oberflächenwasser, Regenwasser und ähnlichem.Die Pumpe hat eine doppelte Wellendichtung und eine Zwischenöl-Kammer, die mit ungiftigem Spezialöl vorgefüllt ist.Die Pumpe verfügt über einen Steigröhrchenanschluss, einen Kühlkörper zur kontinuierlichen Kühlung des Motors durch die gepumpten Flüssigkeit sowie langlebige Rillenkugellager für den Lebensdauerschmierungsbetrieb.Die Pumpe ist gebrauchsfertig ausgestattet mit Tragegriff und wird inklusive eines 10 m Netzkabels geliefert. Das Netzkabel hat einen Steckertyp mit Glasversiegelungsmittel in der Buchse zur Verhinderung des Eindringens von Feuchtigkeit in die Statorwicklung.Flüssigkeit:Flüssigkeitstemperaturbereich:0 .. 55 °CTechnische Daten:Laufradtyp:HALBOFFENMaximale Partikelgröße:12 mmMaterialien:Pumpengehäuse:EdelstahlPumpengehäuse:DIN W.-Nr. 1.4301Pumpengehäuse:AISI 304Laufrad:EdelstahlLaufrad:DIN W.-Nr. 1.4301Laufrad:AISI 304Installation:Pumpenauslass:Rp 1 1/2Maximale Installationshöhe:10 mElektrische Daten:Motortyp:PSCLeistungsaufnahme - P1:0,9 kWRated voltage:Einphasig, AC,230 VRated current:Nennstrom bei Volllast (A):4,4 ACos phi - Leistungsfaktor:Nennleistungsfaktor bei Volllast (cos φ):0,99Rated speed:Bemessungsdrehzahl (U/min):2785 rpmKondensatorgröße - Lauf:C-Rating des Kondensators im Betrieb (F/V):16 F/400 VSchutzart nach IEC EN60529 und DIN40050-9 :IP68Isolationsklasse nach IEC EN60034-5:FNettogewicht der Pumpe ohne Verpackung :12 kgBruttogewicht der Pumpe mit Verpackung :12.5 kg

Adapter-Set komplett DN 40-PN10 30mm

Unilift AP35B.50.06.1.VSubmersible effluent pumpVertical single-stage stainless steel submersiblepump with integrated submersible 1-phasemotor. The pump is fitted with ring stand and carryinghandle and is supplied with a 10 m mainscable. The impeller is a VORTEX impeller for35 mm free passage suitable for pumpingsurface water, groundwater, wastewater andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil. The motor is insulation class F with thermaloverload protection and has long-life deep-groovegreased-for-life ball bearings.The pump has R 2' discharge port and isready for installation either free-standing oron an auto-coupling system.Liquid:Maximum liquid temperature:40 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:R 2'Maximum installation depth:7 mElectrical data:Type of motor:PSCPower input - P1:1 kWRated voltage:1 x 230 VRated current:4.6 ACos phi - power factor:0,98Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug:SCHUKOOthers:Net weight:9.82 kg

15-14 BX PMThe high efficiency Coomfort PM range is a product for domestic hotwater recirculation in 1 and 2 family houses.The motor is a single-phase, 2-pole, hysteresis, permanent-magnet motor in conformity with the EMCdirective.Characteristics and benefits:* Unique AUTOADAPT saves up to 50% heatenergy and 87% motor energy compared with a standard pump in continuous operation* Flushing function* Automatic legionella operation (if supported from the system)* Automatic weekend and vacation function* Temperature control optional* Continuous operation optional* Fast and simple electrical installation due to the million times trusted ALPHA plug* Easy to clean and lime insensitive spheric rotor* Application area up 14°dH water hardness* Wearless operation due to liquid lubricated bearing* No leakage risk due to a static seal* Easy maintenance and cleaning by easy-to-separated motor head that fits on all standard circulation pump housings* Korrosion resistant pump housing in brass* Due to impedance protected motor no motor protection necessary* No additional installation costs due to integrated non return and stop valve in the pump housingLiquid:Liquid temperature range:2 .. 95 °CTechnical:TF class:95Approvals on nameplate:VDE,GS,CEMaterials:Pump housing:Brass MS 68Impeller:Stainless steel, EPDM, PPO, PTFE, GraphitInstallation:Maximum operating pressure:10 barPipe connection:G 1 1/4Port-to-port length:110 mmElectrical data:Max. power input:8 WRated voltage:1 x 230 VCurrent in speed 3:0.07 ACapacitor size - run:0.6 FEnclosure class (IEC 34-5):IP44Insulation class (IEC 85):FOthers:Net weight:1.35 kgGross weight:1.51 kgShipping volume:0.003 m3

MAGNA3 65-60 FMAGNA3 – More than a pumpWith its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.The pump is characterised by the following:• controller integrated in the control box• control panel with TFT display on the control box• control box prepared for optional CIM modules• built-in differential-pressure and temperature sensor• cast-iron pump housing (depending on model)• carbon-fibre-reinforced composite rotor can• stainless-steel bearing plate and rotor cladding• aluminium alloy stator housing• air-cooled power electronicsThe MAGNA3 is a single-phase pump.Characteristic features• AUTOADAPT.• FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).• Proportional-pressure control.• Constant-pressure control.• Constant-temperature control.• Constant-curve duty.• Max. or min. curve duty.• Automatic Night Setback.• No external motor protection required.• Insulating shells supplied with single-head pumps for heating systems.• Large temperature range where the liquid temperature and the ambient temperature are independent of each other.CommunicationThe MAGNA3 enables communication via the following:• wireless Grundfos GO Remote

Unilift AP35.40.06.A1.VSubmersible drainage pump typeVertical single-stage stainless steel submersiblepump with vertical discharge port and integratedsubmersible 1-phase totally enclosed motorin insulation class F with thermal overloadprotection. The pump is fitted with suction strainer and level switch for automatic start and stop.The impeller is a VORTEX impeller for35 mm free passage suitable for pumpinggroundwater, surface water, rain water andsimilar.The pump has a double shaft seal and anintermediate oil chamber pre-filled with non-toxicspecial oil.The pump has a riser pipe, a cooling jacket for continuous cooling of the motor by the pumped liquid and long-life deep-groove greased-for-life ball bearings.The pump is ready for use as it is fitted withcarrying handle and is supplied with a10 m mains cable. The mains cable is ofthe plug type with glass sealing compound in thesocket to prevent penetration of humidity intothe stator windings.Liquid:Liquid temperature range:0 .. 55 °CTechnical:Type of impeller:VORTEXMaximum particle size:35 mmMaterials:Pump housing:Stainless steelPump housing:DIN W.-Nr. 1.4301Pump housing:AISI 304Impeller:Stainless steelImpeller:DIN W.-Nr. 1.4301Impeller:AISI 304Installation:Pump outlet:Rp 1 1/2Maximum installation depth:10 mElectrical data:Type of motor:PSCPower input - P1:0.9 kWRated voltage:1 x 230 VRated current:4 ACos phi - power factor:0,97Rated speed:2810 rpmCapacitor size - run:16 F/400 VEnclosure class (IEC 34-5):IP68Insulation class (IEC 85):FLength of cable:10 mType of cable plug SchukoOthers:Net weight:11.4 kgGross weight:11.9 kg

Mit ALPHA2 GO kann der Installateur nun den Großteil aller Stand-alone-Umwälzpumpen und nahezu 70% der Pumpen ersetzen, die in Fernwärmeunits, Gasheizkesseln und Wärmepumpen nach 2015 integriert sind. Einbaumaß: 130mm

Mit ALPHA2 GO kann der Installateur nun den Großteil aller Stand-alone-Umwälzpumpen und nahezu 70% der Pumpen ersetzen, die in Fernwärmeunits, Gasheizkesseln und Wärmepumpen nach 2015 integriert sind. Einbaumaß: 130mm

Shaft seal BAQE GG D28/spare

Kit, Shaft seal TP(D) cpl 16mm BUBE

Alarmgerät mit Lampe und Hupe für Autoadapt

Tauchpumpe Grundfos UNILIFT KP 150 A-1 ist eine Keller- und Entwässerungspumpe, die mit einem Schwimmerschalter geliefert wird.

Dieses Grundfos UNILIFT KP Modell ist für den Einsatz als Keller- und Entwässerungspumpe vorgesehen und damit für entwässerungsbezogene Pumpaufgaben geeignet.

Der integrierte Schwimmerschalter unterstützt den Automatikbetrieb für eine praktische Wasserhandhabung.