Unidrain Entwässerungsprodukte - Seite 9

The water trap is removable and can be taken apart for cleaning.

Note: The outlet unit can be used in 3 different ways:
– If the water trap is positioned at the top and the top two side spigots are used as inlets from an external unit, then a separate water trap must be installed on the added unit.
– If the water trap is pushed down into the outlet unit, the external unit connected to the top side spigots will be covered by the included water trap, so there is no need for an external water trap.
– If the bottom two side inlets are used, you must establish an external water trap, regardless of the position of the Unidrain water trap.

ClassicLine Rost - Linie - Edelstahl, gebürstet: Anniversario, 800 mm. ClassicLine Anniversario ist ein Rost, der anlässlich des 10-jährigen Jubiläums von unidrain® im Jahr 2013 eingeführt wurde. Der Jubiläumsrost bringt den klassischen Rost näher an die exklusive HighLine-Serie und besteht aus gebürstetem Edelstahl, der zum Rahmen passt.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Available in 8, 10 and 12 mm heights (depending on the thickness of the floor tile). The rubber insert ensures a snug fit inside the unit. A countersunk bearing ensures that the grating fits perfectly into the frame. The frame is non-optional and has two functions: To support the grating and give a perfectly flush finish with the tiled floor.

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

With side drain on the left.

Can be freely positioned against the back wall, independent of any side walls. Only for use with ClassicLine.

Horizontal outlet Ø 75 mm, including water trap.

Two horizontal side inlets, 40 mm, which can be opened as needed. 2 rubber adapters are included so that side inlets can be reduced to 32 mm. Easy access to the removable water trap for cleaning. Meets EN1253 standard and is VA approved.

Rahmen Unidrain 1500 1200/8 mm. (This is already in informal German)

For shower cubicles with open right-hand side, glass screen or similar.

The drain unit has two wall flanges.

Unidrain o-ring for water trap.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

The grating is placed on a countersunk bearing in the frame, to hold it securely.

Only for use with ClassicLine frame.

Outlet-Einheit | Leitung | Ø 50 mm horizontal, inkl. Siphon

Outlet-Einheit | Leitung | Ø 75 mm horizontal, inkl. Siphon

Outlet-Einheit | Leitung | Ø 50 mm seitlicher horizontaler Auslass, inkl. Siphon

The set consists of a panel, rail, heightener set and screws. The set must be assembled before installation.

Includes 2 x hooks to be used for lifting the panel.

The panel solution is placed directly inside the drain unit.

The rail is specially designed to provide a snug fit. Installed with HighLine frame.

The heightener set to adjust the panel is included, so that the panel can be matched to the frame height.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

The set consists of a cassette, rail, heightener set and screws. The set must be assembled before installation. Available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile). Supplement cassette with your own material (e.g. matching floor tile), to complete the solution. The cassette solution is placed directly inside the drain unit. The rail is specially designed to provide a snug fit.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.

Exclusive frame design with upper section of solid 4-mm stainless steel.

Insert ensures a snug fit inside the drain unit.

The frame enhances the exclusive design of the floor drain.

Frame available in 10, 12, 15 and 25 mm heights (depending on the thickness of the floor tile).

NB! Frame height (H) = tile thickness + approximately 2 mm for tile mortar and membrane.